COLLECT run - notes on parameters and DD statements in JCL member COLLECT - syncsort_capacity_management - 12 - 12.40

Use RACF userid and group names in place of accounting data - see later

Specifies that all active tape drives found in the input Type 74 records will be reported on , even if their I/O rate is less than the value of the IORATE parameter, if present. Tape drives with zero I/O rate are not reported.

Capture Coupling Facility data or not

Specifies whether to capture all channel path data from Type 73  records, including offline channels or not at all

Specifies whether to capture CICS data or not

Specifies how Acquire handles CICS dictionary records

Control which CICS summarizations are to be performed

Specifies whether to write a file of CICS response time percentiles - once at the end of the run if CICSRESP=Y or once per output interval if CICSRESP=I

Default means “40 buckets each 0.1 seconds wide"; set the CICS response time buckets, either with discrete values or a range

Generate FTP put and rename commands to push CICS response time data to a user-defined location

Specifies if the date and time of a CICS transaction is to taken from the type 110 record that contained it , when it ended, when it started

The SMF record number of data created by Acquire/DASD

Choose volume, storage group or dataset group processing

Choose how the SMF ID of Acquire/DASD records are to be set - from the Originating system or the Recording system

Default is Y; capture DB2 data or not

If/how to capture DB2 accounting data

How to handle times from DB2 records

What date/time to use for DB2 data, SMF, start or end

Choose which userid to associate with DB2 data

Specifies whether to capture DD Detail data or not

Turn on selective debugging of Acquire modules

Force arbitrary device delay value for bad CMF data

Count of times to wait when dynamically allocation fail

Number of minutes to wait between failing to dynamically allocate a dataset

Use intelligent dynamic allocation of a well-formed datasetname for //SMFDATA

Use intelligent dynamic allocation of a GDG for//SMFDATA

Sets the suffix for DYNAGDG= or DYNADSN=

End date for capture if the end of the input dataset is not encountered first, for example 24AUG09 or TODAY

End time for capture, for example 2300

Names a CICS APPLID in a given system to be excluded from the Capacity Database

Names a DB2 subsystem in a given system to be excluded from the Capacity Database

Control how Acquire terminates if a failure condition occurs

Control how Acquire terminates if gaps in data are detected

Capture HIS data (SMF type 113 subtype 1

Round SMF intervals to minutes, or use the exact time in seconds

Specifies that devices with a lower I/O rate than this will not be included in the output dataset

Collect job/started task/TSO detail by interval or by job end

Collect MQ Series data or not

Collect MQ Series accounting data or not

Collect job detail about OMVS jobs

Control the log messages from Acquire, 1=regular 2=verbose

Default of N indicates that files will be collected from USS by Control Center; if Y, D, M or B files are assumed to be “pushed” from the mainframe to Control Center and are named slightly differently

Construct a “ucopy” command to copy data from z/OS to Windows

Instruct Control Center to overwrite a sample if already present; Control Center will reject the measurement sample if there is no data present for the exact date/time and interval

Earliest start date for capture, for example 17AUG09 or YESTERDAY

Allows user control over number separators and decimal point

Format of SMFDATA file, S for SMF or D for ES/1 databox

Earliest start time for capture, for example 0600

Adjust all times to a specific time zone

Tolerate a z/OS expansion failure of compressed data or not

Compress USS output or not

Control how Acquire deals with a failure condition writing USS data

If Y then Acquire will only write to USS, and not to //ATH­DATA

Path for files if they are to be stored under USS

Control how Acquire terminates if a warning condition occurs

Collect Websphere data or not

If =Y, Convert LPAR weight to percent

Default is Y; use the //WAREHSE file if present to store data that cannot be directly associated with an RMF inter­val